Skip navigation links
14.1.3.2 Optimizing the Synchronization Rate »
Section Navigation      [Toggle]

14.1.3.1. Using Bonded Ethernet Network Interfaces

For a set-up where there is a high-throughput of information being written, you may want to use bonded network interfaces. This is where you combine the connectivity of more than one network port, increasing the throughput linearly according to the number of bonded connections.

Bonding also provides an additional benefit in that with multiple network interfaces effectively supporting the same communications channel, a fault within a single network interface in a bonded group does not stop communication. For example, imagine you have a bonded setup with four network interfaces providing a single interface channel between two DRBD servers. If one network interface fails, communication can continue on the other three without interruption, although it will be at a lower speed

To enable bonded connections you must enable bonding within the kernel. You then need to configure the module to specify the bonded devices and then configure each new bonded device just as you would a standard network device:

  • To configure the bonded devices, you need to edit the /etc/modprobe.conf file (RedHat) or add a file to the /etc/modprobe.d directory.. In each case you will define the parameters for the kernel module. First, you need to specify each bonding device: 

    alias bond0 bonding

    You can then configure additional parameters for the kernel module. Typical parameters are the mode option and the miimon option.

    The mode option specifies how the network interfaces are used. The default setting is 0, which means that each network interface is used in a round-robin fashion (this supports aggregation and fault tolerance). Using setting 1 sets the bonding mode to active-backup. This means that only one network interface is used as a time, but that the link will automatically failover to a new interface if the primary interface fails. This settings only supports fault-tolerance.

    The miimon option enables the MII link monitoring. A positive value greater than zero indicates the monitoring frequency in milliseconds for checking each slave network interface that is configured as part of the bonded interface. A typical value is 100.

    You set th options within the module parameter file, and you must set the options for each bonded device individually: 

    options bond0 miimon=100 mode=1

  • Reboot your server to enable the bonded devices.

  • Configure the network device parameters. There are two parts to this, you need to setup the bonded device configuration, and then configure the original network interfaces as 'slaves' of the new bonded interface.

    • For RedHat Linux:

      Edit the configuration file for the bonded device. For device bond0 this would be /etc/sysconfig/network-scripts/ifcfg-bond0: 

      DEVICE=bond0
BOOTPROTO=none
ONBOOT=yes
GATEWAY=192.168.0.254
NETWORK=192.168.0.0
NETMASK=255.255.255.0
IPADDR=192.168.0.1
USERCTL=no

      Then for each network interface that you want to be part of the bonded device, configure the interface as a slave to the 'master' bond. For example, the configuration of eth0 in /etc/sysconfig/network-scripts/ifcfg-eth0 might look like this:: 

      DEVICE=eth0
BOOTPROTO=none
HWADDR=00:11:22:33:44:55
ONBOOT=yes
TYPE=Ethernet
MASTER=bond0
SLAVE=yes

    • For Debian Linux:

      Edit the /etc/iftab file and configure the logical name and MAC address for each devices. For example: 

      eth0 mac 00:11:22:33:44:55

      Now you need to set the configuration of the devices in /etc/network/interfaces: 

      auto bond0
    iface bond0 inet static
    address 192.168.0.1
    netmask 255.255.255.0
    network 192.168.0.0
    gateway 192.168.0.254
    up /sbin/ifenslave bond0 eth0
    up /sbin/ifenslave bond0 eth1

    • For Gentoo:

      Use emerge to add the net-misc/ifenslave package to your system.

      Edit the /etc/conf.d/net file and specify the network interface slaves in a bond, the dependencies and then the configuration for the bond itself. A sample configuration might look like this: 

      slaves_bond0="eth0 eth1 eth2"

config_bond0=( "192.168.0.1 netmask 255.255.255.0"  )

depend_bond0() {
need net.eth0 net.eth1 net.eth2
}

      Then make sure that you add the new network interface to list of interfaces configured during boot: 

      root-shell> rc-update add default net.bond0

Once the bonded devices are configured you should reboot your systems.

You can monitor the status of a bonded connection using the /proc file system: 

root-shell> cat /proc/net/bonding/bond0
Bonding Mode: fault-tolerance (active-backup)
Primary Slave: None
Currently Active Slave: eth1
MII Status: up
MII Polling Interval (ms): 100
Up Delay (ms): 200
Down Delay (ms): 200
Slave Interface: eth1
MII Status: up
Link Failure Count: 0
Permanent HW addr: 00:11:22:33:44:55
Slave Interface: eth2
MII Status: up
Link Failure Count: 0
Permanent HW addr: 00:11:22:33:44:56